Binding bugs with Turnigy 9v2 & hk tr6a

For model airplanes powered by volts rather than fuel

Binding bugs with Turnigy 9v2 & hk tr6a

Postby ivorn » Wed Jan 25, 2012 9:40 pm

Hi to all my first post.
Have real problems binding my Turnigy 9 with HK tr6a. Going throught the proceedure and still no steady red light.
Most people seem to have no problem, but not working with me.
Does anyone have any answers?

Steps:
Bind plug into batt.
Esc into channel 3
Power up.
Transmitter off.
Hold down bind button.
Turn on transmitter... Nuthin!
:roll:
ivorn
 
Posts: 4
Joined: Wed Jan 25, 2012 9:27 pm

Re: Binding bugs with Turnigy 9v2 & hk tr6a

Postby chrisjunkie » Wed Jan 25, 2012 11:03 pm

Are you sure that the red light is supposed to go solid? I don't remember mine doing that?
chrisjunkie
 
Posts: 45
Joined: Sun Jan 08, 2012 12:10 pm
Location: Eastern Suburbs, Auckland, New Zealand

Re: Binding bugs with Turnigy 9v2 & hk tr6a

Postby FlyingTiger » Wed Jan 25, 2012 11:37 pm

Hold down the bind button and turn on the transmitter first. Then, with the bind plug already in the receiver and with your third hand, plug in the battery to the ESC to power up the receiver. You should now get a solid red light. Now release the bind button and turn off the transmitter. Unplug the battery from the ESC. Remove the bind plug from the receiver. To check, turn on the transmitter and then plug in the receiver. The red light should stay solid.
Gear up and locked!
User avatar
FlyingTiger
 
Posts: 61
Joined: Thu Apr 28, 2011 2:13 pm
Location: Atlanta Georgia USA

Re: Binding bugs with Turnigy 9v2 & hk tr6a

Postby ivorn » Thu Jan 26, 2012 12:28 am

Hi FT, tried that but no luck. Tried esc plugged into 3 socket and next to batt. Errrrrr
Think I'm running out of options...
ivorn
 
Posts: 4
Joined: Wed Jan 25, 2012 9:27 pm

Re: Binding bugs with Turnigy 9v2 & hk tr6a

Postby FlyingTiger » Thu Jan 26, 2012 1:55 am

Watch this video:

http://www.youtube.com/watch?v=zAemTY_w ... _embedded#!

I had it wrong. Turn on the Rx then hold the bind button while turning on the Tx. Release the bind button only after the red light goes solid.
Gear up and locked!
User avatar
FlyingTiger
 
Posts: 61
Joined: Thu Apr 28, 2011 2:13 pm
Location: Atlanta Georgia USA

Re: Binding bugs with Turnigy 9v2 & hk tr6a

Postby ivorn » Thu Jan 26, 2012 3:57 am

Tried that also, no go.Think I've tried every possible combo. Might try on a friends Turnigy. Can't think of what elso to try. Thanks for your help.
ivorn
 
Posts: 4
Joined: Wed Jan 25, 2012 9:27 pm

Re: Binding bugs with Turnigy 9v2 & hk tr6a

Postby RCModelReviews » Thu Jan 26, 2012 7:15 am

Make sure the model memory you're using is in PPM mode not PCM.
RCModelReviews.com, just the facts.
User avatar
RCModelReviews
 
Posts: 2120
Joined: Tue May 04, 2010 3:40 am

Re: Binding bugs with Turnigy 9v2 & hk tr6a

Postby ivorn » Thu Jan 26, 2012 7:24 am

Yes it is PPM.
ivorn
 
Posts: 4
Joined: Wed Jan 25, 2012 9:27 pm


Return to Electric power

Who is online

Users browsing this forum: No registered users and 4 guests

cron